jGun Single Speed – Hytorc (2024)

Table of Contents

01. POWERFUL BREAKOUT 02. REPEATABLE TORQUE 03. ERGONOMIC DESIGN SPECIFICATIONS Imperial Metric ACCESSORIES

Toll Free 1-877-235-4733

The jGun Single Speed is the simple choice for air-powered industrial bolting. With industry-leading power-to-weight and a breakout force that overcomes corroded and damaged nuts, this tool takes over where impact guns and breaker bars don’t cut it.

Contact A Sales Rep

01. POWERFUL BREAKOUT

The jGun provides continuous power with no kickback to break out the nuts that other systems can’t tackle. Impact guns have tremendous vibration and noise and have been banned on many job sites. The jGun uses precision gearing and a simple reaction fixture to give you maximum power without the noise and vibration.

02. REPEATABLE TORQUE

For maximum joint integrity, all of the bolts on a connection need to have an even and accurate load. The jGun system provides adjustable and repeatable torque to ensure that the bolted joint is assembled right the first time and keeps the torque over time.

03. ERGONOMIC DESIGN

The jGun series is built using aerospace materials for lightweight design with maximum durability. The comfort grip and available silencer ensure that the tool operator is comfortable, even on all day jobs.

SPECIFICATIONS

DOWNLOAD SELL SHEET

Technical Data

Imperial

TOOL MODEL	Height (H)	Width (W)	Length (L)	Diameter (D)	Drive	Weight	Torque Range
J-.25	7.06″	2.72″	7.15″	2.50″	¾”	7.2 Lbs.	48 – 259 ft-lbs
J-.5	7.32″	2.74″	8.07″	2.58″	¾”	7.2 Lbs.	129 – 508 ft-lbs
J-1	7.32″	2.74″	8.82″	2.58″	¾”	10.0 Lbs.	275 – 1,125 ft-lbs
J-2	7.94″	3.53″	10.46	3.25″	1″	14.50 Lbs.	521 – 2,190 ft-lbs
J-3	7.94″	3.53″	11.11″	3.25″	1″	15.75 Lbs.	852 – 3,104 ft-lbs
J-5	8.03″	4.15″	12.24″	4.15″	1 ½”	23.20 Lbs.	1,150 – 5,266 ft-lbs
J-8	8.46″	4.23″	13.00″	4.56″	1 ½” – 2 ½”	29.50 Lbs.	1,743 – 7,924 ft-lbs

Metric

TOOL MODEL	Height (H)	Width (W)	Length (L)	Diameter (D)	Drive	Weight	Torque Range
J-.25	179.32 mm	69.09 mm	181.61 mm	63.50 mm	¾”	3.27 Kg.	65.08 – 351.16 Nm
J-.5	185.93 mm	69.60 mm	204.98 mm	65.53 mm	¾”	3.27 Kg.	174.90 – 688.76 Nm
J-1	185.93 mm	69.60 mm	224.03 mm	65.53 mm	¾”	4.54 Kg.	372.85 – 1,525.30 Nm
J-2	201.68 mm	89.66 mm	265.68 mm	82.55 mm	1″	6.58 Kg.	706.38 – 2,969.25 Nm
J-3	201.68 mm	89.66 mm	282.19 mm	82.55 mm	1″	7.14 Kg.	1,155.16 – 4,208.47 Nm
J-5	203.96 mm	105.41 mm	310.90 mm	105.41 mm	1 ½”	10.52 Kg.	1,559.20 – 7,139.76 Nm
J-8	214.88 mm	107.44 mm	330.20 mm	115.82 mm	1 ½” – 2 ½”	13.38 Kg.	2,363.20 – 10,743.53 Nm

Troubleshooting

Tool will not operate

Air motor is seized and needs to be replaced. Confirm recommended FRL lubricator drip (1 drip per every 15 seconds). Make sure air supply is dry.
Gearbox is damaged and requires service.

Tool is leaking oil from exhaust port or handle face

Adjust FRL drip setting to 1 drip per every 15 seconds of operation.

Tool output is too low

Air leaking from coupler or rear cover gasket. Repair or replace fittings or gasket as necessary.
Air motor is worn and needs to be replaced.
Gearbox components may require service/lubrication.
Compressor cannot deliver 30 CFM @ 90 psi.
Plumbing does not meet the minimum requirements (1/2” – 3/4″ diameter hose and 3/8” fittings from compressor to tool).
FRL filter and/or silencer may be clogged.
Calibration date may be expired and tool requires current state calibration.

Tool output is too high

Application may be of “hard joint” nature and tool requires hard joint calibration.
Calibration date may be expired and tool requires current state calibration.

Trigger sticks

Remove trigger rod, clean and lubricate rod and guide bushing.

Tool runs slowly without pulling the trigger

Remove control valve, clean valve & seat. Replace valve if worn excessively.

Clutch will not fully engage in torque or rundown position (DSP tools)

Move shifter ring back towards its original position and tap the trigger (while tool is connected to an air supply). This will change the input shaft orientation and will now allow the ring to fully engage in the opposite direction.

Loose gearbox housing screws

Replace and install as necessary using permanent strength thread locker.

Excessive square drive damage/extraction

Poor reaction point. Make sure reaction point is down near the bottom or “flat” section of the reaction arm paddle. If your reaction arm does not fit your application use a more appropriately configured reaction fixture.

Impact function is weak (ZGUN and Thrill Gun)